|
Is my camera supported by NUUO products via ONVIF ?
Description
How to verify ONVIF support for my cameras?
Do NUUO products support Muliti-stream, PTZ control, Motion Detection, IO,and Talk of my camera via ONVIF ?
Note: based on Device Pack version 3.5 and above
Solution
1. Please make sure that you use "Device Pack" version 3.5 and above on NUUO products
2. Please make sure you have ONVIF test report, and this report contains two parts:
A. Declaration of Conformance, and B. ONVIF Conformance Test Report
A. Declaration of Conformance
B. ONVIF Conformance Test
4. Please make sure your camera supports Profile S with Test Tool version 12.06 at least on "Declaration" part
5. Please make sure the test result is "PASSED" on page 2 of "ONVIF Conformance Test Report":
6. Please make sure that ONVIF service port on your camera is 80 (sync. with http port), if not, please ask manufacturer for the correct port.
7. Please make sure that, according to the features you request,
the required test items are NOT test failed on the test report:
8. For Multi-stream support: Your camera must support more than 1 profile,
and the below test items must be passed, therefore they should not be found in failed items:
Media Configuration – Media Profile
MEDIA-1-1-1 MEDIA PROFILE CONFIGURATION
MEDIA-1-1-2 DYNAMIC MEDIA PROFILE CONFIGURATION
Media Configuration – Video Configuration
MEDIA-2-1-1 VIDEO SOURCE CONFIGURATION
MEDIA-2-1-2 VIDEO ENCODER CONFIGURATION
MEDIA-2-1-3 JPEG VIDEO ENCODER CONFIGURATION
MEDIA-2-1-4 MPEG4 VIDEO ENCODER CONFIGURATION
MEDIA-2-1-5 H.264 VIDEO ENCODER CONFIGURATION
9. For PTZ support: (PTZ, preset, home)
the below test items must be passed, therefore they should not be found in failed items:
PTZ – Move Operation
PTZ-3-1-3 PTZ RELATIVE MOVE
PTZ-3-1-4 PTZ CONTINUOUS MOVE
PTZ-3-1-5 PTZ CONTINUOUS MOVE & STOP
PTZ – Preset operations
PTZ-4-1-1 SET AND GET PRESET
PTZ-4-1-2 GOTO PRESET
PTZ-4-1-3 REMOVE PRESET
PTZ – Home Position operations
PTZ-5-1-1 HOME POSITION OPERATIONS (CONFIGURABLE)
PTZ-5-1-2 HOME POSITION OPERATIONS(FIXED)
Imaging – Imaging Settings (Focus)
IMAGING-1-1-1 IMAGING COMMAND GETIMAGINGSETTINGS
IMAGING-1-1-9 IMAGING COMMAND SETIMAGINGSETTINGS
Imaging – Focus Move
IMAGING-2-1-5 IMAGING COMMAND RELATIVE MOVE
IMAGING-2-1-7 IMAGING COMMAND CONTINUOUS MOVE
IMAGING-2-1-13 IMAGING COMMAND STOP
10. For Motion Detection and IO support:
There are total 3 criterias should be met:
A. Below key words have to be in the notification body
MD: Motion / Inside
DI : Alarm / Port / Input
DO : Relay
B. ONVIF supports 3 event notification methods, and NUUO only supports two of them.
“Basic Notification”
“Real-time Pull-Point Notification”
“Notification Streaming” (Metadata)
--> If your camera uses "Basic Notification" method, it is NOT supported by NUUO
C. The below test items must be passed, therefore they should not be found in failed items:
Device Management – I/O
DEVICE-5-1-1 IO COMMAND GETRELAYOUTPUTS
DEVICE-5-1-3 IO COMMAND SETRELAYOUTPUTSETTINGS
DEVICE-5-1-5 IO COMMAND SETRELAYOUTPUTSTATE – BISTABLE MODE (OPENED IDLE STATE)
DEVICE-5-1-6 IO COMMAND SETRELAYOUTPUTSTATE – BISTABLE MODE (CLOSED IDLE STATE)
Event Handling – Event Properties
EVENT-1-1-2 GET EVENT PROPERTIES
Event Handling – Real-Time Pull-Point Notification Interface
EVENT-3-1-9 REAL TIME PULLPOINT SUBSCRIPTION – CREATE PULL POINT SUBSCRIPTION
EVENT-3-1-15 REAL TIME PULLPOINT SUBSCRIPTION – PULLMESSAGES
Media Configuration – Metadata Configuration
MEDIA-5-1-1 METADATA CONFIGURATION
11. For Talk support: No specific test case is needed currently, however
your camera MUST support RTSP back channel
12. If you have confirmed the above 11 items, and still your camera can't not be supported by NUUO products, please contact us via eHelpdesk with ONVIF test report.
|
│Contact Us │ Site Map│ Privacy Statement │
